Showing Stock for Collection from

Filter Products +-

Brand

Colour

Diameter

System Components

Material

Length

Application

Fuel Type

Flue & Chimney > Chimney Cowls & Flue Terminals

Chimney Cowls & Flue Terminals - C5

Chimney Cowls and Flue Terminals

One of the most important components of the install is the chimney cowl and/or flue terminal. It marks the termination point of the flue system and provides a safe point from which gases and particulates are released into the atmosphere. Cowls and terminals also provide protection from the elements- wind and rain and some come with fitted mesh to prevent birds from entering the chimney system. Our range of cowls and terminals come from highly reputable and experienced manufacturers, such as Schiedel for ICID twin wall systems, Selkirk for both twin wall and single skin flue systems and MAD cowls from JD Burford for single skin systems. We stock a very wide range of cowls and flue terminals, for gas, oil and solid fuel appliances, so if you are experiencing a specific problem with your flue system, come and talk to us and we can help you find the best solution for the problem.


Read more...
Currently there is no regulation that requires that a pre-existing chimney be lined. However, the installer of any appliance must satisfy themselves that the chimney is suitable for the appliance and the fuel being used. In houses built prior to 1965 lining was less common. Flues were usually ‘parged’ (rendered) on the inside with a lime mortar. This parging suffers attack from acid and tars produced during combustion and as a result deteriorates over time. It is not uncommon for flues to leak fumes or tars into the walls or other parts of the house. For properties of and over this age the likelihood that lining will be required is good. In properties built since the introduction of the 1965 building regulations, all flues must be built with liners during their construction. This is usually done with clay or concrete liners, which should last the life of the building. However, many houses built since 1965 do suffer from chimney problems (examples detailed below) due to badly installed liners and would therefore need to be lined. There are a number of reasons why a chimney may need to be lined: • The chimney leaks smoke and fumes into other rooms or parts of the building • Condensates or tar are seeping through the chimney walls causing staining (This could be inside or outside the building) Most traditional chimneys are square however chimney brushes are round, therefore there are areas of the chimney that remain unswept. By lining a chimney using circular flexible liner you can ensure that when it is swept it is completely free of tars. • The manufacturer of the appliance specifies that the chimney be lined in the appliance installation instructions • The flue is much too large for the type of appliance that is being installed and would not draw properly • The flue is too cold and is not drawing properly (chimney on an outside wall) • The chimney was built after 1965 but was installed incorrectly (liners fitted upside down etc) • The old flue surface is eroded and rough, causing frictional resistance to the flow of gasses resulting in poor up draught. • If you have recently had your chimney swept and bits of mortar were brought down with soot this may be evidence of poor condition. A chimney can be pressure tested by sealing it off at the top and bottom and by using smoke pellets to test for leaks in the property (and where applicable adjoining properties). However, this can be a costly method, the costs of which would make up a proportion of the costs of lining the chimney anyway.
Distribution Centre Stock:
More than 5
£68.68
£57.23
Logo for MAD Cowls
Distribution Centre Stock:
More than 5
£30.46
£25.38
Logo for MAD Cowls
Distribution Centre Stock:
From 29/03
£16.80
£14.00
Logo for MAD Cowls
Distribution Centre Stock:
More than 5
£68.68
£57.23
Logo for MAD Cowls
Distribution Centre Stock:
More than 5
£41.90
£34.92
Logo for MAD Cowls
Distribution Centre Stock:
More than 5
£68.68
£57.23
Logo for MAD Cowls
Distribution Centre Stock:
More than 5
£89.46
£74.55
Logo for Schiedel
Distribution Centre Stock:
More than 5
£6.00
£5.00
Logo for Tower Flue Components (TFC)
Distribution Centre Stock:
Up to 5
£10.40
£8.67
Logo for MAD Cowls
Distribution Centre Stock:
More than 5
£49.27
£41.06
Logo for MAD Cowls
Distribution Centre Stock:
Up to 5
£30.46
£25.38
Logo for MAD Cowls
Distribution Centre Stock:
Up to 5
£16.80
£14.00
Logo for MAD Cowls

Loading More Results

please wait